Parts for Lg WT7900HBA/00: Outer Case Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer tub cover assembly that installs on top of the outer tub. Replace this cosmetic component if your original cover is cracked, broken, or missing.

Suspension damper reduces vibration and noise during washer spin cycles. Replace if your washer shakes excessively or makes loud banging sounds. Verify fit with your model number before ordering.

Replace your washer's rear access panel if cracked, damaged, or missing. This outer cabinet panel covers the back of your washing machine assembly.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

Washer holder assembly that secures internal components in place. Replace if the original holder is cracked, broken, or missing to restore proper fit.

Fix poor cleaning or clothes tangling in your washer with this pulsator assembly. Direct replacement for top-load models. Moderate DIY repair.

The Customized Screw is an OEM part for securing the wash plate in LG washing machines. This screw maintains the wash plate's position and stability during the washer's operation. The Customized Screw ensures the wash plate performs efficiently, contributing to the effectiveness of the washing process by enabling proper agitation and circulation of clothes.

Causes of a bad Customized Screw can include wear and tear over time, especially from the constant motion and stress during the wash cycles.  

Symptoms of a bad Customized Screw include:

• The wash plate becoming loose or detached
• Ineffective washing due to improper motion of the wash plate
• Unusual noises during the wash cycle indicating a loose component

This OEM LG part is also compatible with some Kenmore models.

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls

Adjustable leveling leg that supports your washer and allows height adjustment. Replace if damaged, stripped, or missing to restore stability on uneven floors.

Hardware washer that sits beneath screws or nuts to distribute load and secure fasteners. Replace if bent, missing, or worn to restore proper fit.

Replacement mounting bracket holder that secures internal washer components. Needed when your original bracket is cracked, broken, or missing.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

Outer trim piece that finishes your washer door for a clean look and protects components. Replace when damaged, faded, or to restore appearance. Confirm fit with your model number.

Replaces a cracked, broken, stripped, or missing control knob on your dryer or washer. Restores secure grip and proper engagement with the control shaft.

Fix a washer that won't start, stops mid-cycle, or has unresponsive controls with a new power control board assembly. Manages motors and sensors.

Washer not draining or making groaning noises during drain cycle? This drain pump assembly removes water and debris. Check for clogs first; moderate DIY.

Fix intermittent washer operation with this single wire harness. Restores secure electrical connections between components for reliable performance.

Suspension rod assembly for front-load washers. Stabilizes the drum during spin cycles. Replace if rods are bent, broken, or rubber mounts are worn.

This drain hose directs used water from your washer to the household drain. Replace if cracked, split, leaking, or chewed through by rodents.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a factory replacement parts assembly designed to restore proper fit and function of a specific component group in your appliance. Use it to replace a worn, damaged, or missing original assembly and maintain reliable operation. What it does:

• Provides a complete, preassembled component group specified by the manufacturer
• Restores proper alignment, support, and operation of the associated parts
• Helps resolve issues like looseness, rattling, misalignment, or intermittent function
• Direct-fit replacement engineered to match the original design

• One parts assembly

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Refer to your model's service documentation for the exact location and procedure
• Handle sharp edges and components carefully; wear cut-resistant gloves
• Verify correct operation before final reassembly

Replace your washer's guide cover if it's cracked, broken, or missing. This cover protects the internal guide mechanism and maintains proper operation.

If your washer won't start or shows a door lock error code, a faulty lid switch assembly is likely the cause. This safety switch detects proper closure.

Fix washer not draining or leaking water with this drain hose assembly. Replaces cracked, leaking, or blocked hoses that prevent proper drainage.

Secures internal components to the washer frame. Replace if cracked, bent, or broken to restore proper alignment and stop rattling or sagging parts.

Secures internal washer components in proper alignment. Replace this mounting bracket if cracked, rusted, broken, or missing to restore stability.

Fix detergent not dispensing or leaking from your washer drawer. This dispenser assembly restores proper flow and prevents buildup. Easy DIY fix.

Fix poor cleaning or uneven water spray in your washer with this tub spray nozzle assembly. Directs water during wash cycles. Moderate DIY repair.

Fix a washer that won't fill, leaks underneath, or drips constantly with this water inlet valve. Controls water flow into the drum. Easy DIY repair.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

Fixes washer drum not spinning or spinning intermittently. The stator assembly powers the motor that rotates the wash basket. Moderate difficulty repair.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Fix E6 error codes and loud ratcheting sounds during wash or spin cycles. This washer motor assembly drives drum rotation for proper cleaning.

Fix intermittent power issues or unresponsive controls with this washer wire harness. Routes electrical signals between components for reliable operation.

Replace your washer's filter assembly housing to trap debris and maintain proper water flow. Install when you notice reduced performance or clogs affecting reliability.

Secures brackets, panels, and fasteners inside your washer. Replace this nut if worn, missing, or stripped to restore tight connections and eliminate rattling.

Small flat hardware washer that sits under screws or bolts on washer assemblies. Distributes load and protects surfaces. Replace if missing or worn.

Washer not heating water or showing tE error? This temperature sensor monitors water temp and signals the control board. Moderate DIY repair fixes temp issues.

This heater assembly replaces the dryer's heating element and housing to restore warm airflow for drying cycles. It's a direct-replacement assembly that re-establishes the appliance's heat source when the dryer won't heat properly. What it does:

• Houses the electric heating element that produces heat for drying cycles
• Replaces a burned-out element, open circuit, or damaged housing that can stop the dryer from heating
• Helps resolve symptoms such as no heat, only air tumbling, or weak/partial heating
• Works with the dryer's blower and thermostat to deliver consistent drying temperatures

• One heater assembly (heating element installed in housing)

• Disconnect power to the dryer (unplug or shut off breaker) before servicing
• Allow components to cool and wear gloves to protect hands from sharp edges
• Verify the part number matches the dryer's parts list before installation

Snap-on trim cap that conceals fasteners and openings on your washer. Replace if cracked, broken, or missing to restore finished appearance.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.