Kenmore Washer Dryer Combo 110.5810850 (1105810850, 110 5810850) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 8009
Original Whirlpool light bulb, 40 watt.
Symptoms of needing to replace the light bulb include:
- Dimming or flickering light
- Complete lack of illumination inside the appliance
- Visible signs of damage or burnout on the bulb itself
Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.
Do-It-Yourself Stories from Customers like You
Jennair jjw9630cas double oven doors did not close all the way and the light would not go out Wayne W. • East Longmeadow , MA • February 13, 2016
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it...
Read more
More
$18.23
- Compare At:
-
$21.69
- You Save:
-
$3.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002263
Illuminates the dryer drum for better visibility when loading and unloading. Replace when bulb burns out or fails to light. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Squeaky noise and not fully drying David H. • Santa Clarita , CA • September 20, 2019
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking.
I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was...
Read more
More
$15.55
- Compare At:
-
$18.50
- You Save:
-
$2.95
Genuine Whirlpool part
By: Whirlpool
Part Number: 285452A
Filters debris from water entering your washer and seals the hose connection. Replace if water fills slowly or screens are clogged. Confirm fit by model.
Do-It-Yourself Stories from Customers like You
Water puddle on floor at front left corner; glass lid dripping water on soap dispenser from splashing and leaking down side panel onto floor Ronnie M. • Phoenix , AZ • June 25, 2019
As a Mechanic, I did the common sense approach:
INITIAL OBSERVATIONS & CHECKS:
- Unplug Machine & check inlet water hose connections for leaks and signs of hose failure;
- Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows...
- Inspect...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694674
The Cycling Thermostat is an OEM part for Whirlpool dryers. It regulates and monitors the temperature inside the dryer during the drying cycle. It ensures that the dryer doesn't overheat and prevents potential damage to clothes or the dryer itself.
Causes of a faulty cycling thermostat can include wear and tear over time, electrical issues, or sensor malfunction.
Symptoms of a bad cycling thermostat may include:
- Clothes taking longer than usual to dry
- Inconsistent drying results
- Overheating or burning smell
- The dryer not heating at all
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Too hot
-
No heat or not enough heat
-
Shuts off too soon
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer not heating properly Hashem N. • Los Angelos , CA • October 26, 2014
This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years.
Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy.
Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work.
I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I...
Read more
More
$48.46
- Compare At:
-
$57.67
- You Save:
-
$9.21
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.48
- Compare At:
-
$8.98
- You Save:
-
$1.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP356138
The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.
Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.
Symptoms of a bad spring tension hose clamp include:
- Water leaks around hose connections
- Loose or disconnected hoses
- Unusual noises or vibrations during operation
- Water pressure issues within the washing machine
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Water leak Steven K. • New City , NY • August 10, 2018
Took off cover, installed new parts.
Read more
More
$9.63
- Compare At:
-
$11.46
- You Save:
-
$1.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP353244
Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.
Do-It-Yourself Stories from Customers like You
My kenmore washer model 11029828801 was agitating during the fill cycle and the tub would only partially fill also at the end of the spin cycle rinse water was spraying in resoaking the clothes Jay S. • Hammond , IN • February 07, 2017
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new...
Read more
More
$53.21
- Compare At:
-
$63.32
- You Save:
-
$10.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160
This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.
- Connects water tubing between components within the appliance's water system
- Helps maintain a tight, leak-resistant seal at the joint
- Restores proper water flow when a tube or connector is damaged
- Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit
What's included: One adapter tube assembly. Install notes:
- Disconnect power and shut off the water supply before servicing
- Relieve line pressure and place a towel or pan to catch any residual water
- Note routing and orientation before removal to ensure correct reassembly
- After installation, restore water and check all connections for leaks
Do-It-Yourself Stories from Customers like You
Washer not filling with cold water Stephen S. • Bronx , NY • July 24, 2016
Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks.
Cold water settings now work properly again.
Read more
More
$11.78
- Compare At:
-
$14.14
- You Save:
-
$2.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP660658
This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.
Do-It-Yourself Stories from Customers like You
The dryer motor stopped working. Kenneth M. P. • Saint Clair Shores , MI • December 05, 2021
I ordered a replacement motor from APP and installed it myself.
Read more
More
$10.37
- Compare At:
-
$12.44
- You Save:
-
$2.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP76314
Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A
Do-It-Yourself Stories from Customers like You
Bad fill hose. Rick D. • Maywood , NJ • January 05, 2022
Replaced hose and washers.
Read more
More
$34.75
- Compare At:
-
$41.00
- You Save:
-
$6.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16272
Leaking water connection? This hose coupling creates a secure seal between your washer hose and water inlet, stopping drips and loose connections. DIY fix.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP17258
This rubber bumper cushions and protects moving parts and panels, reducing noise and preventing metal-to-metal contact. It restores proper spacing and stops rattles so doors, drawers or panels close smoothly and quietly. What it does:
- Acts as a shock-absorbing cushion to prevent damage from impact or slamming
- Reduces vibration and rattling noise from doors, drawers or panels
- Maintains proper clearance and helps parts align during operation
- Commonly replaced when worn, flattened, missing or causing noise
What's included:
Install notes:
- Typically press-fits into a hole or onto a mounting post
- Clean the mounting surface of dirt and old adhesive or debris for best retention
- No special tools required for most installs; use gentle pressure or a blunt tool to seat the bumper
- Unplug the appliance or disconnect power before servicing
Do-It-Yourself Stories from Customers like You
I needed to replace the parts purchased Deonauth S. • Brooklyn , NY • November 14, 2024
By my self
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: WP52185-1
A small flat washer used with fasteners to distribute load, prevent pull-through, and reduce wear on mating surfaces. Simple, durable hardware that helps maintain secure assemblies in laundry appliances. What it does:
- Provides a smooth bearing surface between a fastener head or nut and the appliance component
- Helps distribute clamping force to prevent damage or pull-through of softer materials
- Reduces loosening from vibration and helps maintain a stable connection
- Commonly replaced when hardware is corroded, deformed, or missing
What's included: One flat washer. Install notes:
- Disconnect power and water supply and follow all safety precautions before servicing the appliance
- Use the correct matching fastener and seating orientation for reliable fit and function
- Inspect surrounding hardware and replace any corroded or damaged bolts, nuts, or mating parts
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10068250
$2.64
- Compare At:
-
$3.12
- You Save:
-
$0.48