Kenmore Washer Dryer Combo 417.99375100 (41799375100, 417 99375100) Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 137292700
Dryer drum won't turn or making loud banging noises? A broken drum belt is the likely cause. This belt connects the motor to the drum for rotation.
Do-It-Yourself Stories from Customers like You
Broken dryer belt. Peter U. • Biloxi , MS • December 12, 2020
Replaced the belt.
Read more
More
$6.95
- Compare At:
-
$11.79
- You Save:
-
$4.84
Genuine Frigidaire part
By: Frigidaire
Part Number: 131825900
Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.
This part fixes the following symptoms
-
Marks left on clothes
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Dryer would not turn on Kathie R. • Burlington , WI • January 15, 2016
The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible.
Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem.
Next step was to...
Read more
More
$10.71
- Compare At:
-
$12.74
- You Save:
-
$2.03
Genuine Frigidaire part
By: Frigidaire
Part Number: 134511600
Drive belt connects motor to drum for wash and spin cycles. Replace if washer won't spin, clothes stay wet, or you smell burning rubber. Verify fit.
This part fixes the following symptoms
-
Spins slowly
-
Burning smell
-
Pumps but will not spin
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$23.61
- Compare At:
-
$28.10
- You Save:
-
$4.49
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303931775
Dryer won't heat or stops heating after 10-15 minutes? Gas valve coils control burner ignition. Simple 5-10 minute repair with video guide included.
This part fixes the following symptoms
-
No heat or not enough heat
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Our dryer didn't heat Larry L. • Poway , CA • November 10, 2014
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits.
I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have.
I looked up my dryer, decided what was probably the problem,...
Read more
More
$26.95
- Compare At:
-
$34.51
- You Save:
-
$7.56
Genuine Frigidaire part
By: Frigidaire
Part Number: 131658800
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.
This part fixes the following symptoms
-
Door won't close
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Drum stopped turning loud 60 hz hum from motor James S. • Winchester , TN • November 03, 2018
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts.
Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum...
Read more
More
$54.25
- Compare At:
-
$65.10
- You Save:
-
$10.85
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304516871
Traps lint and debris during drying to prevent vent clogs and maintain efficiency. Replace when torn, rusted, or bent. Verify fit with your model.
Do-It-Yourself Stories from Customers like You
Needed a new lint filter my unit was torn. Dennis A. • Cooper City , FL • March 21, 2014
Ordered a new one from the website, matched the model and the picture
Read more
More
$42.95
- Compare At:
-
$51.11
- You Save:
-
$8.16
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281135
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Our dryer didn't heat Larry L. • Poway , CA • November 10, 2014
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits.
I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have.
I looked up my dryer, decided what was probably the problem,...
Read more
More
$42.95
- Compare At:
-
$55.90
- You Save:
-
$12.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 5308027429
The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets
Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.
Symptoms of a bad high temperature adhesive include:
- Components or parts becoming loose or detached
- The adhesive becoming brittle or cracked
- Inability to properly bond surfaces exposed to high heat
- Visible deterioration or peeling of the adhesive
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This part fixes the following symptoms
-
Marks left on clothes
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Clothes getting stuck in front of dryer then later on a grinding and loud noise when spinning Michael G. • Chicago , IL • August 23, 2020
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose."
The cause of the scraping and loud...
Read more
More
$52.68
- Compare At:
-
$62.69
- You Save:
-
$10.01
Genuine Frigidaire part
By: Frigidaire
Part Number: 3204405
Enables smooth drum rotation in your washer. Replace if you hear loud roaring or whirling noises during spin cycle. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$78.78
- Compare At:
-
$93.75
- You Save:
-
$14.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 131476300
The Blower Wheel is an OEM part for Frigidaire clothes dryers. This component works to propel hot air through clothes during drying cycles.
Causes of a bad blower wheel involve wear from years of operation, such as bearing deterioration or plastic fan blade cracking/warping. Foreign object damage or improper cleaning techniques pose other risk factors.
Symptoms of a bad blower wheel include:
- Slow or weak drying even on high heat settings
- Loud clanking or grinding noises from inside the duct
- The dryer not activating or functioning when turned on
- Reduced air discharge observable at the vent
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Fan making banging sound in housing Keith N. • Kaukauna , WI • April 25, 2015
The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance.
Read more
More
$39.95
- Compare At:
-
$47.54
- You Save:
-
$7.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 5308002401
The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles.
Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components.
Symptoms of a bad spin-bearing washer involve:
- Vibration or shaking noises coming from inside the washer cabinet
- Belt slippage wasting energy by inefficiently spinning loads
- Increased friction resulting in longer cycle times for spins
- Failure of belts or other components from unsupported bearing
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
Do-It-Yourself Stories from Customers like You
Noisey bearing on spin cycle Neal G. • Klamath Falls , OR • February 14, 2016
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple.
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Frigidaire part
By: Frigidaire
Part Number: 134190200
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
-
Will not fill with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
The washer was filling very slow especially cold water. Wayne S. • Oakland , MD • February 10, 2023
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent...
Read more
More
$103.95
- Compare At:
-
$124.74
- You Save:
-
$20.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303207102
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer door would not stay closed Carolina L. • Miami , FL • September 08, 2015
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch.
I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to...
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Frigidaire part
By: Frigidaire
Part Number: 131724301
The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.
Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.
Symptoms of a bad drum bearing bracket include:
- Excessive vibration or shaking during operation
- Loud grinding or scraping noises
- The dryer drum not spinning properly or at all
- Premature wear of the drum bearing
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$9.63
- Compare At:
-
$11.56
- You Save:
-
$1.93
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281019
Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303937186
The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles.
Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines.
Symptoms of a faulty ignitor can include:
- The dryer fails to start or stop heating intermittently
- Cycles taking overly long to complete or feel uneven
- Excessive service calls relating to "no heat" troubles
- Risk of uncombusted gas pooling in dryer if ignition falters
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Gas smell in the dryer after a cycle completed no smell outside the dryer (until i opened the door!) Matthew M. • Mcfarland , WI • April 25, 2016
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in...
Read more
More
$66.78
- Compare At:
-
$79.47
- You Save:
-
$12.69