Kenmore Washer 110.20022010 (11020022010, 110 20022010) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8281163
Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.
Do-It-Yourself Stories from Customers like You
Whirlpool wtw5000dw1 top loader door would not lock, spin cycle would not function John C. • Cornelia , GA • December 24, 2021
Replaced door latch and switch. Parts are plastic so you must know what you are doing to avoid breaking new parts. Videos were hard to find for my model - eventually I found a video that addressed a different problem but required disassembly of a washer cabinet similar to mine. I removed the control panel using a putty knife and unplugged the wire to the latch switch. Then I remove 3 screws securing the washer's top panel to the back panel. Using a rubber mallet, I gently knocked the top panel...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: 285863
Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.
Do-It-Yourself Stories from Customers like You
Washer drain hose not long enough Ray P. • Frankfort , IL • February 07, 2016
I ordered the drain extension kit and the hose connector kit.
Read more
More
$30.95
- Compare At:
-
$36.83
- You Save:
-
$5.88
Genuine Whirlpool part
By: Whirlpool
Part Number: W10739673
Adjustable leveling leg screws into washer base to stabilize and level your machine on uneven floors. Replace worn, missing, or damaged legs for stability.
Do-It-Yourself Stories from Customers like You
The washer was shaking badly during the spin cycle David W. • Sarasota , FL • November 27, 2018
I replaced the drive block & leveling feet, it helped a lot but the washer still shakes a lot, I am now going to try replacing the suspension rod kit, These were the most recommended fixes to the problem.The repairs were not too hard, I wish I had a spanner wrench, I couldn't find it on the website.
Read more
More
$11.51
- Compare At:
-
$13.70
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W10846509
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
- Loose or detached rear bulkhead allowing side-to-side play
- Excessive noise and shaking felt through the surrounding walls
- Development of micro-cracks around screw holes over time
- Potential leak paths if holes are no longer sealed
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Whirlpool direct drive washer major repair drive/brake assembly clutch suspension outer tub etc Carter H. • Oak Ridge , TN • July 11, 2015
Watched several repair videos on YouTube produced by AppliancePartsPros.com for this model Whirlpool washer (videos quite well done). Purchased parts from AppliancePartsPros.com; order correctly filled and parts arrived by FedEx within two working days. Performed repairs as instructed. "Plastic welded" holes in poly outer tub using similar plastic (PP) using a cheap soldering iron - worked perfectly, saved >$150 for new tub. Washer now like brand new. Suggestion - buy the spanner wrench,...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 8212638RP
Contains two, six foot long braided hoses with 90 degree ends.
Do-It-Yourself Stories from Customers like You
Kenmore fh error code Michael H. • Cataula , GA • January 18, 2015
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had...
Read more
More
$48.37
- Compare At:
-
$57.08
- You Save:
-
$8.71
Genuine Whirlpool part
By: Whirlpool
Part Number: 285835
Connects washer drain hose to extension hose. Includes coupling and clamps. Replace if cracked, broken, or when extending drain hose length to reach pipe.
Do-It-Yourself Stories from Customers like You
Washer drain hose not long enough Ray P. • Frankfort , IL • February 07, 2016
I ordered the drain extension kit and the hose connector kit.
Read more
More
$34.95
- Compare At:
-
$41.24
- You Save:
-
$6.29
Genuine Whirlpool part
By: Whirlpool
Part Number: 8212487RP
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Do-It-Yourself Stories from Customers like You
Water inlet was obstructed Jessica C. • Mount Shasta , CA • April 15, 2018
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result.
Read more
More
$40.95
- Compare At:
-
$48.73
- You Save:
-
$7.78
Genuine Whirlpool part
By: Whirlpool
Part Number: W10759923
Replacement retaining nut for washers and dryers. Secures components like pulleys, shafts, and assemblies. Order a new nut if yours is stripped or missing.
Do-It-Yourself Stories from Customers like You
Would not go into spin cycle automatically Daniel H. • Marlborough , MA • March 01, 2015
Have had this experience before. Ordered the same parts as last time plus a few more related components. Performed the repair in under an hour. All is good.
Read more
More
$4.95
- Compare At:
-
$5.94
- You Save:
-
$0.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10327522
This timer knob mounts on the appliance's mechanical timer shaft and lets you select cycles and settings. Replace a cracked or stripped knob to restore smooth, positive control of the timer and accurate cycle selection.
- Attaches to the timer shaft so you can set cycle and time
- Provides a secure grip for selecting and adjusting settings
- Common symptoms: knob spins without moving the timer, feels loose, cracked, or missing
- Helps restore proper engagement when the hub is worn or stripped
What's included: 1 timer knob Install notes:
- Disconnect power before servicing
- Pull the old knob straight off the timer shaft
- Align the flat/splines of the new knob with the shaft and press on firmly
- Rotate through a full turn to confirm proper engagement
Do-It-Yourself Stories from Customers like You
Dryer timer knob broke Michael S. • South West City , MO • March 19, 2017
Replaced timer knob.
Read more
More
$46.31
- Compare At:
-
$55.11
- You Save:
-
$8.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.85
- You Save:
-
$1.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$17.95
- Compare At:
-
$21.36
- You Save:
-
$3.41
Genuine Whirlpool part
By: Whirlpool
Part Number: W10371566
Outer tub assembly holds wash water and houses the inner basket in top-load washers. Replace if cracked, leaking, or damaged during repairs.
Do-It-Yourself Stories from Customers like You
Outer tub. Richard C. • Ludlow , ME • February 05, 2022
Got all required parts and completed the job in 3 or 4 hours.
Read more
More
$253.95
- Compare At:
-
$286.74
- You Save:
-
$32.79
Genuine Whirlpool part
By: Whirlpool
Part Number: 8212545RP
Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.
Do-It-Yourself Stories from Customers like You
Whirlpool Cabrio displayed lf would not complete a wash cycle. Brandy H. • Colorado Springs , CO • August 25, 2020
Purchased water inlet valve and new hot and cold water hoses. Unscrewed about 5 screws that were holding the top of the washer in place then slide the top forward and up. Released the control top it popped off no screws. Disconnected the wires attached and unscrewed 2 screws holding the valve in place the popped that off. Popped in a new valve and repeated the process in reverse. Boom done! Very simple works like new!
Read more
More
$37.95
- Compare At:
-
$44.78
- You Save:
-
$6.83
Genuine Whirlpool part
By: Whirlpool
Part Number: 8212546RP
Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489128
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Whirlpool part
By: Whirlpool
Part Number: 285448A
Hardware washer distributes load under fasteners to prevent loosening and reduce vibration. Replace when missing or damaged to restore secure fit.
Do-It-Yourself Stories from Customers like You
Wash machine water inlet valve Larry E. • Coleharbor , ND • February 18, 2017
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running.
Read more
More
$5.34
- Compare At:
-
$6.30
- You Save:
-
$0.96