Steve October 08, 2014 for Model Number mdbh950aww The latch is broken on front of unit. what do I need to buy to relace that part?
1 Answer Steve, The part needed would be WPW10130695 Dishwasher Door Latch Assembly. This is a complete latch assembly and contains the latch, door switches, and handle. You should have everything you need. Read More...
Maggie February 28, 2014 for Model Number mdbh950aww The white plastic in front of the latch is broken off. I have to use a spatula to open and close. Can this pane be installed to replace broken part?
1 Answer Hello Maggie. You need to order and replace part number WPW10130695 in the unit. Read More...
Rich November 14, 2013 for Model Number MDBTT59AWW I have a dishwasher model # MDBTT59AWW, I need the front control panel. The one that says will work doesn't look the same as the one I have, in the middle of the panel is the start button & delay button. The picture shows nothing in the middle. On the left I have 4 buttons the one in your picture only has 3. I can't get the picture big enough to read the buttons.
1 Answer Hello Rich. The manufacture has changed the par to 6-917726. It should work for the model number provided. Read More...
Lindsey July 30, 2013 for Model Number MDBTT59AWW We are looking to replace the control panel on our Maytag quiet series 100 dishwasher. The buttons will not work. It looks like the poly flex circuit has some damage, so we were told to replace the panel. 1. Does the poly flex circuit (or ribbon as it is called) come with the panel? 2. How do you install the panel? There are no instructions I am told. Model #: MDBTT59AWW Serial #: 23681467EJ Part #: AP4364676
1 Answer Lindsey, Yes the panel does come with the ribbon harness. To replace the control panel you will remove the screws holding the inner door panel. Once removed you will lift the door panel up and there are 4 screws that hold the control panel to the front panel. remove the screws. Once this is done then you can remove the latch assembly and the control board and lift the panel off and install the parts and reassembly the unit. Read More...
David June 19, 2013 for Model Number Mdbh955aww My dishwasher will not start only one light on the control panel lights up. No start button lights. Any idea.?
1 Answer Hello David. Based on the information you provided, it sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Steve November 27, 2012 for Model Number mdbtt59awb My dishwasher takes 6 to 7 times to start. Finally starts. Was told it may be the control panel. Also thought it could be the timer. Can you please give me your input? Thank you
1 Answer Hello Steve. If the unit stops and all lights go out, you will need to order and replace the control board 99003160, not the control panel in the unit. Read More...
Vinnie August 23, 2012 for Model Number mdbh950awb when i go to start my my maytag quiet series 100 dishwasher i press start the lights come on but nothing happens, then i turn it off and it makes noise like it wants to run. can this be i control panel issue?
1 Answer Vinnie, You're on track, You most likely have an issue with the keypad on the control panel 6-917726. Faulty keys can make the dishwasher operate irratically. We'll send you some information so you can test the keypad circuits and run a couple of control board tests to determine the issue. Thanks Read More...
Jaybob August 09, 2012 for Model Number MDBH950AWB ONLY LIGHTWASH AND RINSE LIGHTS UP AND WHEN I PUSH START THAT LIGHT GOES ON THEN THEY BOTH GO OFF,NOTHING HAPPENS. I DID GET IT TO GO ON BY HITTING LITE WASH AND 2 HR DELAY.HAD TO HOLD LITE WASH DOWN TO KEEP LIGHTS ON. PLEASE HELP,CONTROL PANEL WAS CHANGE OUT 2 YEARS AGO. THANKS
1 Answer Jaybob, Sounds like you'll need to replace the control panel / keypad assembly 6-917726 again. We'll send you the information you need to test the key pad circuits with a multimeter, so yuou can verify the failure. This time check in the control panel and inner door liner for water marks and condensation, and make sure the exhaust vent tube seals against the foam pad on the inside of the panel. Read More...
Dennis July 22, 2012 for Model Number Maytag MDBH950AWS plastic tub A while back our dishwasher was leaving dirty water at end of cycle. I replaced the drain pump. I ran the dishwasher and the pump kept running. Asked for your advise, and you said it was the float switch,replaced that and the pump keeps running, whats next?
1 Answer Hello Dennis. You will need to check and make sure the float is making contact with the switch and turning it off, and make sure there is no broken or bad wires in the wiring harness. Read More...
1 Answer William, Apparently not. We don't understand "control panel cover only". The 6-917726 Control panel, is a complete assembly, it has the keypad panel, control panel assembly and the exhaust vent seal. It is available as a "complete assembly" only. Good Luck and Thanks Read More...