Roper Switch

• Will not stop filling with water
• Will not fill with water

I took the washer apart and replaced the water level switch and hose with new ones. I followed the video that I found on youtube (which is on the site) and had no problems at all. Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

• No hot or cold water

I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more

First and foremost I UNPLUGGED THE OVEN!. I'll pass on the early morning SHOCK THERAPY! Second, I unscrewed aluminum protection plate from back of oven. Next, I unplugged the two connections behind the oven switch. Then I removed the plastic switch from the front and unscrewed the two screws that secured the oven switch to the oven. Once you've completed all these steps you take your new oven switch and do everything again but in reverse order. Hope this was informative, direct, and that your... Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

• Will not stop filling with water
• Will not fill with water

Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more

Removed front of dryer panel, removed top, and removed drum. Replaced motor and wheel, because the old wheel was rusted on the motor shaft, and could not be removed, so I had to break it off. Replaced motor, and reassembled. Everything works now. I also replace the switch-Pb, because the start button was getting stuck. Read more

Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem. Read more

• Light not working

We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND... Read more

SSVD48600Pon finally popped the control panel loose from the top of the stove. Took some manipulation as the stove is more than 20 yrs. old With a screwdriver finally popped the switch loose. Applied the new switch. Popped the top back to the control panel. Put the screws back in and everything was back to normal. Read more

I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it. I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair! Thank You Read more

• Will not fill with water

Relaced the switch and hose. Water stops properly now and not over filling onto the floor. Read more

I watched the repair video AppliancePartsPros.com had on each repair and followed the instructions. Read more

Initially suspected timer, but it did advance during some cycles. the schematic on the unit and other input on this site helped to confirm that the water level switch was at fault Read more

Removed rocker switch,made up jumper so the compactor could be used while awaiting replacement switch. The part came 2 days later and was installed in less tha 5 minutes. Unit working like new again. Thanks for the great service!! Read more