General Electric Range / Cooktop / Oven Screws, Nuts, Washers

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more

I took the cover off and the fan had separated from the bushing. Ordered a new fan and nut and it took all of 5 minutes to replace. Probably saved $159.99 service call repair and that is with a coupon. Any one can do this repair, just make sure the oven is cold as you will come in contact with metal parts. Read more

Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more

It was very easy!. Just removed the screws off the trim plate and access was right there. The double oven was given to me but the handles were missing and the end caps so I just had to replace them. Read more

We replaced the broken door hinge. Read more

My son-in-law helped me. He pulled the liner open enough that he could see he just had to tighten up the existing screw on the door handle.. For the liner, we put a new screw in each side and tighted it up. At first we were afraid it was in the hole the screw went into but finally got it to screw in tightly. Back in business!!! Read more

Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more

My husband gets irked when I take it upon myself to do appliance repair. This isn't my first project. I looked at various websites and found this one very helpful. Information was consistent with what the GEappliance website had. Video instilled confidence that the job could be simply done. Price was right and a new ignitor module was installed; easy peasy! Appliance works like new! Read more

I replaced the transformer. Did not fix the problem and the new transformer overheated and failed as well. Your support person suggested the ignition module is bad. I bought a new igniter box and you replaced the transformer. The transformer got hot with only the harness connected. I found a short in one of the switches. I bought the harness, connected everything and it worked Read more

Second repair after 10 years of service - igniter had cracked and spill overs were causing the others to misfire. This was a two-step process. I took apart the cooktop to see what parts were neded. Screws were all rusted, I had to drill ome out. The burner gaskets broke during the process and needed replacement. One of the burners had deformed due to excess heat. After that initial diagnose, I reassembled the cooktop without the igniters and ordered all the parts I needed. The second stage was... Read more

I used the parts ordered, minus the screw because it was not the right one, and replaced the burner. I just took the old parts off and put the new parts on. Super easy fix! Read more

Purchased new burner assemblies and burner grates from Appliance Parts Pros to replace old, worn out ones. This job was easy as all parts purchased were unpack and place. My range is about 15 years old but is in pristine condition so instead of replacing the range, I chose to replace dirty, worn parts. Read more