General Electric Valve

I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more

• Will not fill with water

Pulled out the unit, found the inlet valve was leaking. Went on AppliancePartsPros.com and ordered a new valve. That was Saturday evening. Tuesday I got my part and installed it. Thanks for the fast delivery. Read more

• Will not drain

Replaced the solenoid and bracket assembly Read more

• Ice maker won't dispense ice
• Door sweating
• Frost buildup

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Will not drain

I ordered a new pump on this website. They provided me with written directions as well as a video to follow along with on how to change the pump. As always it wasn't as easy as the video, but that was the mechanic no the tool! Great job on the service. Will order parts from here again. Read more

• Not dispensing water
• Leaking
• Ice maker not making ice
• Ice maker won't dispense ice

To verify if you have a bad valve in the first place read on... I first pulled out the ice maker to remove all the frozen water including the inlet section which was a huge solid waterfall of ice. While it was out completely disconnected I cleaned/chipped out the freezer section ice puddle. I also completely melted the ice cubes and ice puddles off the ice maker at the fill bucket end in the sink with running water careful to not get water near the power cord area. I then put a tall plastic cup... Read more

• Leaking
• Ice maker not making ice
• Ice maker won't dispense ice

I replaced the water inlet valve. The toughest part was closing off the feed line while I waited for the valve to be delivered. The needle valve used to install the feed line wouldn't close completely. I ended up fabricating a plug from some parts from the hardware store. The mounting bracket on the new valve was completely different from the original, but it still mounted easily enough. The 1/4" plastic hose fitting was a different type from the original, but the hose fitted into it easily... Read more

• Will not drain

It is very simple to fix. All the blogs recommend replacement of this part but do not explain why. This is a normally open check valve that permits the water from inside the dishwasher to drain out, either once it gets too high or just general splash. When the machine drains the pump comes on and the check valve closes. If the check valve is damaged or worn (like mine was) some of the water can pump back into the machine. So really, the problem is not that the machine will not drain but... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered water inlet valve. Two screws to take out. Disconnect the hose. Disconnect the two wires. Put in the new valve. Reverse the procedure. Whole thing took about 10 minutes. Read more

1.) Located where the water leak was coming from in the refrigerator. 2.) Unplugged the refrigerator. 3.) Shut off the water supply to the refrigerator. 4.) Unscrewed the back cardboard panel. 5.) Unscrewed the Water Valve attached to the side of the refrigerator (one screw). 6.) Disconnected the three electrical plugs on the water valve. The plugs are different sizes so there is no need to worry about reconnecting incorrectly. 7.) Disconnected the two water lines by pushing down on... Read more

• Will not fill with water

Removed the old one. ordered a new one from appliancepartspros.com on Thursday afternoon, had the part on my front porch by Friday afternoon and installed it the next Monday morning. After I determined the problem, actual time fixing was maybe 30 minutes. Read more

My husband fixed it, he took out the leaky valve and replaced it with the new valve, which we received in the mail from your company, which was only a short time after we ordered it. Thank you for being so prompt. Our washer is only a little over 2 years old and upon looking online, we found out this model has since been discontinued due to problems. The parts are no longer available from GE, so we were thrilled to find your company online which carried the part. It saved us a lot of money... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

I reseached these error codes and compared them to others problems. After deciding that I was gonna order the part and fix it myself I was at ease to find out it took 10min to fix! And it actually worked! The washer was pausing during cycles, cloths were soaking wet, spin cycle only worked on drain and spin at the end of the Ioad (it would spin slowly otherwise), soap dispenser still had the soap in it or it would be filled with water after the cycle was over. I watched videos on how to change... Read more

• Will not fill with water

I took the inlet valve apart, found it was clogged with sediment, so I cleaned it and reinstalled it. Water was still not filing, so I figured the valve was sticking. I ordered a new valve,because $30 was a lot cheaper than a new dishwasher. I took out the old valve with two screws, and disconnected the supply line, the brass elbow, one hose, and a wiring harness. I reattached it in the same place, re-using the all the other parts, and once I turned the power and water back on, it worked as... Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

• Will not fill with water
• Will not drain

Put in the new parts and now it does not leak anymore. Very simple Read more