Jenn-Air Parts

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Spins slowly
• Pumps but will not spin
• Will not agitate

My Maytag washer make a loud screech when the washer tub needed to be stopped by the brake. Last year, I had replaced the suspension springs, the snubber ring, the drive belt and the drain pump. Those repairs worked fine, but a few weeks later, the screeching noise started. So I figured it was the brake system. I thought it would be better to replace the brake rotor and stator together as a set since I was going to disassemble both and they were 18 years old anyway. I decided to replace the... Read more

I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more

I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

First time DIY dryer repair. Videos very helpful! Remove front. Found glides worn thin, paint on drum removed where glides located. Drum, cage and motor turned easily - must be OK. Thirteen year old dryer. Order glides & felt, might as well replace belt and rollers while there. First time order - could not have been easier! Received 2nd day. Replaced parts, reassembled & connected power. Ran for 3 minutes with scraping noise then stopped with burning odor. Disassembled dryer, smelled odor from... Read more

New glides, idler had a crack, blower retaining ring was gone. And a good clean out. Like new again for 2 hours and $77.00 Read more