Need Help?
Call or text
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.
Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more
Replaces worn, dull, or damaged 21-inch mulching blades on walk-behind mowers. Features curved design for effective mulching. Upgrade your rusty blade.
Replaced some baffles and the blade Read more
Internal hose that channels water from the washer's outer tub to the drain pump. Replace if cracked, leaking, or worn to prevent puddles under the machine.
Removed front of washing machine, loosened clamps, got wet, replaced hose, tightened clamps, tested hose--no leaks--job done. PLEASE, PLEASE put up a description indicating the length of hose, measured along its length, is 15." It will save other folks wondering if they ordered the wrong item. Thank You. Read more
Control cable for walk-behind mowers. Connects throttle or self-propel controls to engine or drive system. Replace if cable is broken, frayed, or stretched.
Ordered and installed new cable Read more
This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.
Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more
Secures pins and shafts on lawn tractors and riding mowers. Replace if bent, missing, or worn. Bow-tie design inserts through pre-drilled holes.
Replaces broken or sheared auger shear pin on snow throwers. This safety part snaps when auger hits obstacles to protect engine from damage.
Spindle assembly for lawn tractor mower decks. Connects blade to drive belt for cutting operation. Replace if cracked, worn, or damaged bearings.
Flange lock nut secures components on mowers and outdoor power equipment. Replace if stripped, corroded, or missing to restore proper fastening.
Removed old scraper blade. Filed away bent edges where casing was worn. Installed new scraper blade and bolts. added a backing plate to body where erosion occurred. East repair. Best part was that big snowstorm was forecast for Wednesday night. 12-18 inches expected. Parts arrived on Wednesday morning, right at time predicted. I was up and running before the snow hit (actually only got 6 inches. So much for the Storm of the Century) Read more
Side discharge chute for walk-behind mowers. Directs grass clippings away from mower deck. Replace if cracked, broken, or missing to prevent clogging.
I replaced the part. I ordered it and the shipping was very fast. The part fit perfectly and I will buy again from Appliance Parts Pros. Read more
Hex bolt secures blade adapter and other components on lawn mowers. Replace if bolt is stripped, damaged, or missing to properly fasten parts.
Bought the replacement part and bolted it right on! Read more
Ground drive belt transfers engine power to the transmission and wheels. Replace if mower loses self-propel function or wheels stop turning. Verify fit with your model number.
Hex screw for lawn mowers, tractors, and snow blowers. Replaces worn, corroded, or missing screws on engines and housings. Identical fit for secure assembly.
This is a flanged lock nut. It’s designed to apply tension, typically on a joint that needs to have a certain amount of flex. As such, it’s mostly used on snowblower chutes and lawnmower handles. They can remain in place, but with a forgiving connection that can take a beating. The nut size is 3/8, with a thread size of 16. A lock nut will generally last for many years. However, the silicone ring inside will wear down if it’s frequently tightened and loosened. It needs to be replaced when it will no longer reliably remain in place. Generally, this begins as a symptom of slight slippage and worsens as time goes on. Thankfully, whether it’s being used on a snowblower or a lawnmower, this nut is generally straightforward to access. Simply unscrew the old nut, then screw the new nut on until it’s nice and tight. Our flanged lock nuts are genuine OEM MTD nuts, and they are sold individually.
New steering column. Read more
Steering pinion gear connects the steering column to the front axle turning mechanism on riding mowers. Replace if worn, stripped, or damaged.