Bob August 27, 2013 for Model Number maytag neptune mah3000aww Stated out with the door lock not activating and the spin not spinning. Replaced door wax motor and control board. All worked fine for three washes. Now the machine will not drain the water in the tub, I think it spins but slow, more likely the slowness is because of the water in the tub. I also replaced the timer. Could I have gotten a bad board that failed or ??? What's left to replace or should I just replace the machine?
1 Answer Hello Bob. Access the pump and see if it is clogged and if there is power coming to it. If there is power there, it is not clogged, and does not drain, replace the pump on the unit. Read More...
Gary L May 20, 2013 for Model Number MAH3000AWW Serial 25122487UM. I need replacement confirmation of this control board for my SN. Thanks.
Maurizio F. May 14, 2013 for Model Number WASHER MAYTAG MAH3000AWW SERIAL # 25121585UF Please confirm the part number of the control board that I should buy. Thanks.
1 Answer Maurizio, according to your model and serial the replacement control board is part number 22002988. Thanks! Read More...
Mike April 14, 2013 for Model Number MAH3000AWW I need to replace the control board for a Maytag MAH3000AWW. The serial number is 35274708WB. There are two listed. Which is the correct one? Thanks.
1 Answer Mike, according to your model/serial you'll use control board part number 22002988. Thanks! Read More...
Burnt April 02, 2013 for Model Number MAH3000AWW Maytag Neptune washer Serial # 36277133WB. What would be the parts # for the control board for this unit?
Tom March 15, 2013 for Model Number MAH3000AWW I have a Maytag Neptune front loader model# MAH3000AWW that will go thru all the cycles but will not spin in the spin cycle. Both the door lock and the on lights are illuminated thru the entire process. Any thoughts on the problem.
1 Answer Tom, You will want to check the spin enable switch on the unit. It is possible that the door lock light be on and the door to be locked but the latch is not depressing the spin enable switch in order to allow spin. Read More...
Katie February 01, 2013 for Model Number MAH4000AWW Our washer has been making loud noises in the spin cycle, would shut off between rinses and I'd have to push start to get it going again. I cleaned the inlet screens and that corrected that problem, and we changed the bearings and seal kit. The washer is not spinning out now. I have also replaced the wax motor and the pump drain. Is it likely we will have to replace the motor and board to fix our spin problem? After the above repairs, the machine did a test cycle great, and I washed one load of clothes and it spun out fine. Then the next load it wouldn't spin. We also checked the belt and it did not have any flaws that we could see. We checked the board and didn't see any burnt out spots. Thanks so much for your help!
1 Answer Hello Katie, You will want to check the spin enable switch to make sure that it is good. A way to test is to put into spin cycle and jump the last switch on the door lock which has a red and yellow wire. If the unit spins then you need the spin enable switch. Read More...
Kris January 31, 2013 for Model Number Maytag Neptune washer #MAH5500BWW My washer does not spin after it takes in the water. The door lock light is on and the door is actually locked. Please advise which parts to change.
1 Answer Hello Kris, You will want to check the control board for burnt terminals. Also check the lock enable switch to make sure that it is engaging. If it is not engaging the unit will not spin. Also check the Motor control board for power when the unit is supposed to be spinning. If you are getting power to the motor control board then the motor control or motor would be faulty. Read More...
Luc F January 28, 2013 for Model Number MAH3000AWW I change the bearing not that long ago and need to fix the board also it was bunt between R103 and pin 0 of conector P7. Ran fine for 2 weeks now the board is burn R52 and Q3 ??
1 Answer Hello Luc, The R52 resistor is for for the timer motor. You will want to check the relay on the machine control board and check the connections to the timer for loose connections. You will want to replace the machine control board 22002988. Read More...
Donald T January 12, 2013 for Model Number mah3000aww serial # 331134511jy which control board do I need