Parts for Kitchenaid KHWV01RSS0: 05 - Tub And Basket Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer won't spin or makes noise? This retaining nut secures pump and motor components. Common cause of leaks and wobbling. Basic tools needed.

Replace your washer's drive pulley if worn, wobbling, or has damaged mounting flats. Installs on the tub shaft to transfer belt motion to the drum.

Transmits power from motor to rotate the washer tub. Replace if worn, cracked, or causing squealing. Tight fit is normal during installation. Verify fit with your model number.

Ventilation pipe for your washer. Installs on the tub assembly to allow air circulation. Replace if cracked, broken, or accumulating dirt and debris.

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

Replace your washer's outer tub when you hear loud dragging sounds during spin or notice water leaks near the bearing. Fixes worn bearings and restores wash performance. Check fit by model number before ordering.

Rear

Replaces the large stationary outer tub that holds water and supports the inner basket. Order when tub is cracked, leaking, or structurally damaged.

Includes spider and shaft.

Plastic baffle that mounts inside the washer drum to lift and tumble clothes. Replace if cracked, broken, or missing. Snaps into place on drum wall.

Replace this washer O-ring seal to stop leaks and restore watertight connections. Install when you notice drips or water damage at joints. Verify fit.

Front counterweight that mounts to the washer's outer tub. Replace if cracked, broken, or missing to restore proper balance and reduce vibration during spin.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Suspension spring kit for front-load washers. Supports the tub assembly to maintain balance during cycles. Replace if springs are broken, stretched, or missing.

Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.

Secures hoses and seals to the washer tub for leak-free operation. Replace if damaged or weakened to prevent leaks. Confirm fit with your model.

Replacement outer tub for front-load washers. Houses the spin basket and seals water inside during wash cycles. Replace if cracked, damaged, or leaking.

Push-in nut secures counterweights, panels, and trim to washer tub studs. Replace when cracked, stripped, or missing to eliminate rattling.

The Shock Absorber is an OEM part for Whirlpool washing machines. This component is essential for reducing vibrations and stabilizing the washer drum during operation, particularly during the spin cycle. It helps to absorb shocks and minimize excessive movement, ensuring the washing machine runs smoothly and quietly.

Note: The unit requires a quantity of 4. Package includes 1 only; order as needed.

Symptoms of a failing Shock Absorber include:

• Excessive shaking or vibrating of the washing machine, especially during the spin cycle
• Loud banging or thumping noises during operation
• The washing machine moving or "walking" across the floor
• Visible damage or wear to the shock absorber

Causes of a bad shock absorber can include wear and tear from regular use, heavy or unbalanced loads that put extra strain on the absorbers, or physical damage from impacts or mishandling.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Secures washer panels and components to the cabinet. Replace if your mounting bracket is cracked, broken, or missing to restore proper alignment.

Includes water temperature sensor.

The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal W11590578. Order separately if needed. 

Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.

Symptoms of a bad water temperature sensor include:

• Inability to switch between wash steps or advance through the cycle
• Erratic or inconsistent temperature readings
• Failure alarms or error codes displayed
• Improper or incomplete washing even on high heat settings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Self-tapping screw used in range assembly. Features 8-18 thread size and 0.375 inch length. Also used in some washer models as cross-appliance hardware.

Self-tapping screw used in range assembly. Features 8-18 thread size and 0.375 inch length. Also used in some washer models as cross-appliance hardware.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.