Washer Dryer Combo Clip Or Clamp
Genuine Lg part
By: Lg
Part Number: 2W20017E
Secures the outer door gasket to prevent water leaks during wash cycles. Replace if rusted, corroded, or the seal isn't holding tight. Confirm fit with model.
Do-It-Yourself Stories from Customers like You
Washer basket was loose banging/knocking when running eventually gave a 'load out of balance code" Dwayne D. • Hopewell Junction , NY • September 29, 2014
The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should...
Read more
More
$20.95
- Compare At:
-
$24.72
- You Save:
-
$3.77
Genuine Whirlpool part
By: Whirlpool
Part Number: 285790
The Clutch Band and Lining Kit is an OEM part for Whirlpool washing machines. It contains the clutch band and clutch lining components essential for proper transmission of power from the washer motor to its drum during the spin cycle. The clutch band and lining allow for a controlled amount of slippage to safely extract water from clothes without damage.
Symptoms of a bad clutch band and lining include:
- Excessive noise or vibration during spin
- Slow or ineffective spinning
- The drum failing to spin or “locking up”
- Premature wear of other transmission parts
Over time and with heavy use, these components can wear down. If slipping or damage is detected, it’s important to replace the kit to avoid potential transmission repairs.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Spins slowly
-
Will not agitate
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Squealing during spin cycle and very weak agitation Elijah S. • Stockton , CA • May 24, 2015
My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe...
Read more
More
$46.31
- Compare At:
-
$55.57
- You Save:
-
$9.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.31
- Compare At:
-
$8.77
- You Save:
-
$1.46
Genuine Lg part
By: Lg
Part Number: 4861ER2001D
Secures the inner door gasket to prevent water leaks during wash cycles. Replace if gasket is loose or leaking. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Lg washer/dryer combo unit shook upper counter balance weight loose damaging the mount lugs on the tub cover and tore the tub gasket Christine V. • Saluda , VA • March 28, 2020
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back...
Read more
More
$28.95
- Compare At:
-
$34.16
- You Save:
-
$5.21
Genuine Lg part
By: Lg
Part Number: 4861FR3068A
The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.
Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.
Symptoms of a bad clamp include:
- Water leaking from hose connections
- Hoses coming loose or detaching during operation
- Visible rust or damage on the clamp
- Poor water flow or pressure issues
This OEM LG part is also compatible with Sears/Kenmore models.
Do-It-Yourself Stories from Customers like You
Bad bearings seal and spider David R. • Jacksonville , FL • February 04, 2017
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it.
After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.)
Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with...
Read more
More
$11.95
- Compare At:
-
$14.10
- You Save:
-
$2.15
Genuine Lg part
By: Lg
Part Number: 4930FR3040A
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Do-It-Yourself Stories from Customers like You
Lg washer was rocking really badly and the drum was hitting the sides during every spin cycle and even coming off the top spring mount Benjamin M. • Lynchburg , VA • January 18, 2016
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm!
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Frigidaire part
By: Frigidaire
Part Number: 134242400
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Buzzing noise when the motor was powered Richard K. • Wilton , CT • April 22, 2024
Replace idler, motor mounting clamp and lock
Read more
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Genuine Whirlpool part
By: Whirlpool
Part Number: 279220
Includes two bumpers and two locking clips. You will use one or the other depending on hole size.
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$12.32
- Compare At:
-
$14.54
- You Save:
-
$2.22
Genuine Whirlpool part
By: Whirlpool
Part Number: 285353
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Do-It-Yourself Stories from Customers like You
Washer would agitate but would not go into high spin sounded like spin was working though Mario M. • Corona , CA • January 03, 2015
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks.
Door sensor...
Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly.
Timer...
In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Lg part
By: Lg
Part Number: 4860FR3092C
Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.
Do-It-Yourself Stories from Customers like You
Loud noise during spin cycle Steven S. • Celina , OH • March 10, 2019
I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful.
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Ge part
By: Ge
Part Number: WH1X2036
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
Do-It-Yourself Stories from Customers like You
Drain hose was leaking Haide H. • Chatham Township , NJ • May 01, 2017
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job.
Read more
More
$15.95
- Compare At:
-
$18.82
- You Save:
-
$2.87
Genuine Frigidaire part
By: Frigidaire
Part Number: 134737300
Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Leaking hose. Sherry W. • Auburndale , FL • December 02, 2017
New hose and clamp.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Ge part
By: Ge
Part Number: WH01X10595
Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 3161433
Secures shafts and components to prevent axial movement, wobble, and noise. Replace if worn, damaged, or loose to restore proper alignment. Confirm fit.
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Genuine Lg part
By: Lg
Part Number: 4861FR3068M
This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:
- Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
- Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
- Reduces vibration-related noise caused by loose hoses or wires
- Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues
What's included:
Install notes:
- Disconnect power to the appliance before servicing; shut off water supply if working with water lines
- Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
- Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
- If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware
More
$11.60
- Compare At:
-
$13.80
- You Save:
-
$2.20
Genuine Frigidaire part
By: Frigidaire
Part Number: 3205821
This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:
- Secures trim pieces, panels, or grill components to the appliance frame
- Prevents loose or rattling parts that can cause noise or misalignment
- Holds components in correct position so doors and panels close properly
- Replaces worn or broken clips that no longer grip reliably
What's included: One clip Install notes:
- Remove power or disconnect the appliance before servicing when applicable
- Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
- Inspect mating surfaces and replace any additional damaged fasteners for best fit
More
$41.95
- Compare At:
-
$50.34
- You Save:
-
$8.39
Washer dryer combo replacement parts are essential for keeping your laundry routine running smoothly. Whether it's to maintain efficiency or to restore full functionality, having the right parts on hand can make all the difference.
Your washer dryer combo is a workhorse, handling both washing and drying in a single unit. The clips and clamps in these machines play a crucial role in securing hoses and connections, ensuring everything operates without leaks or malfunctions. Properly functioning washer dryer combo parts keep the performance high and prevent issues like inefficient cycles and potential water damage.
Using OEM replacement parts is highly recommended. These original equipment manufacturer parts are designed specifically for your machine, ensuring compatibility and high-quality performance. Clips and clamps that match your washer dryer combo's specifications can maintain its integrity and longevity.
No need to fret over finding the right parts; high-quality clips and clamps for your washer dryer combo are readily available. Investing in these essential components will keep your appliance running like new, ensuring efficient and trouble-free laundry days.
More